Call +44 (0)161 439 5683     sales@woodfordtooling.com

Planer Thicknesser Knives Setting

Regular serrations over the surface could also be thanks to the metal infeed roller pressure being set too onerous, crushing the wood deeper than the cutting circle of the cutter block. This never happens with a rubber-coated roller. Strive weakening of the pressure slightly with the adjusters.

With rubber feed rollers the coating will typically twist on the central spindle to create a lamp. This leads to an awfully jerky feed and leaves widespread dirty marks wherever the rubber grips intermittently. If the wood stops feeding altogether, it should be that you simply area unit taking too significant a cut or the board is slightly tapered and has corroded. Scale back the depth of cut and it ought to begin feeding once more.corroded

Feed in just one piece of timber at a time. Unless you've got a sectional feed roller newer place many slim items of various thickness along as a result of the thickest piece may elevate the Infeed roller afar from the diluent ones that may then be discharged backwards.

Indentations and bruises on a Thickness board will be caused by poor chip clearance at the Cutterblock, With bears shavings being ironed into the cut surface of the Outfeed roller. Make certain the mud chute isn't blocked associate degrees invariably connect with an extractor. If chippings square measure allowed to accumulate on the Thickness table associate degree odd one might become tried underneath the board, leading to an extended score knock off the length of the Undersurface, Thus invariably feed the work onto the tip of the Thickness table to push any clippings out of the method.

Planer-Thicknessers need terribly correct putting in place if we are using  the simplest out of them and lots of new users are nervous of the method, consequently, died knives in way too long and soldiering on with blunt blades rather than taking them out for re-sharpening. Not solely will this lead to an awfully poor end, however, a blunt planing machine is harder to use safely as a result of the timber bounces around instead of cutting swimmingly.

The distinction between a planing machine operating well and dealing badly is meant in terms of blade adjustment. It can not be exaggerated simply, however, necessary this setting is, as incorrectly set, knives lead to a machine that either will not plane the least bit, planes tapers or takes huge scoops out of the top of the work. With properly set blades the timber ought to plane absolutely from finish to finish. You must not leave it overlong and so discontinue the dodgy bits once planning.

Do not assume it's properly discovered straight out of the box. Rough handling in transit is often enough to knock the tables out of line and have an effect on all the settings.

Sniping and jamming

The most obvious indicator of a badly set blade is sniping, wherever an oversized scoop is taken out of the top of the board as you pass it over the plane. It will be caused by poor feeding technique, however, is typically the results of the blades being started too high on the block.

If the blades are terribly low the timber can jam because it hits the top of the outfield table. If they're solely a fraction too low the cut can step by step taper away to zilch as you pass the timber over the block. Notwithstanding what percentage times you repeat the cut, it'll continually taper off.

Both these symptoms are simply cured, however, you wish to figure terribly rigorously and build minute changes till it's right. Be ready to form many tries to induce it to spot on, however, the trouble is well worth because the plane feels entire completely different once it's caught dead with each knives properly set.

Before you create any changes it's very important to disconnect the machine.

Next, Drop the infeed table well approach down to get the picture out of the way, as a result of all settings are created relative to the mounted Outfeed table.

Slacken off the holding bolts on the lockup wedges by winding them into the wedge. Solely use the wrench given the machine, significantly after you are alteration up. Don't suppose that you can just get further pressure by employing a longer one. It's deliberately short to prevent you overtightening and Remotion the fine threads on the lockup bolts.

The design of the tapered safety wedge implies that the blades cannot fly out though they become loose, therefore, don't go mad with the alteration pressure.

You will wind the bolts well into the wedge before you'll be able to take away the full assembly, however, it'll eventually embark together unit.

Blade Type :

Essentially, there are 2 forms of the  blade, skinny ambiguous disposables or the thicker re-Sharpenable ones which can or might not be double sided.The advantages of disposable blades That are after the holder is ready up they slot into position while not additional adjustment, they're double-edged therefore you get 2 sets with one try, and that they are the simplest possibility for beginners.

Re-Sharpenable planer blades are also cheaper than a replacement set of disposables, however ,they need to be Reground to get a recent edge, should be reset on every occasion to account for the loss of breadth by the grinding method, and there's an extended, additional concerned, conversion amount.

Leave a Reply